Klimaire KSIO018-H221 Installationshandbuch PDF herunterladen

1. Determine hole positions according to left and right

side of the installation plate. The hole center is obtained

by measuring the distance as shown in the diagram above.

2. Dirll the piping plate hole with φ65mm hole-core drill.

3. Drill the piping hole at either the right or the left and the

hole should be slightly slanted to the outdoor side.

4. Always take steps to protect the pipe when drilling metal

grid,metal plate or the like.

INSTALLATION MANUAL FOR

KSIO ROOM AIR CONDITIONER

(Split Wall-Mounted Type)

DRILL A HOLE IN THE WALL

INSTALLATION PLATE MOUNTING

Please read these safety precautions carefully before installation

Be sure to follow all the precautions below, they are all important for ensuring safety.

This symbol indicates the possibility of death or serious injury.

This symbol indicates the possibility of injury or damage to property.

1) This equipment must be grounded and installed with ground leakage current breaker. It may cause

electricalshockifgroundingisnotperfect.

2) Do not install the unit at place where leakage of flammable gas may occur. In case gas leaks and

accumulates at surrounding of the unit, it may cause fire.

3) Carry out drainage piping as mentioned in installation instructions. If drainage is not perfect, water

may enter the room and damage the furniture.

1) Install according to this installation instructions strictly. If installation is defective, it will cause water

leakage,electricalshock,orfire.

2) Use the included accessories parts and specified parts for installation. otherwise, it will cause the set

tofall,water leakage,electricalshock, orfire.

3) Install at a strong and firm location which is able to withstand the set s weight. If the strength is not

enoughorinstallationisnotproperlydone,thesetwilldropandcauseinjury.

4) For electrical work, follow the local national wiring standard, regulation and this installation instructions.

Anindependentcircuitandsingleoutletmustbeused.Ifelectricalcircuitcapacityisnotenoughor

defectfoundinelectricalwork,itwillcauseelectricalshock, or fire.

5) Use the specified cable and connect tightly and clamp the cable so that no external force will be acted

ontheterminal.Ifconnectionorfixingisnotperfect,itwillcauseheat-uporfireattheconnection.

6) Wiring routing must be properly arranged so that control board cover is fixed properly. If control board

coverisnotfixedperfectly, it will overheatatconnectionpointofterminal,fireorelectricalshock.

7) When carrying out piping connection, take care not to let air substances other than the specified

refrigerantgointorefrigerationcycle.Otherwise,itwillcauselowercapacity,abnormalhighpressure

intherefrigerationcycle,explosionandinjury.

8) Do not modify the length of the power supply cord or use of extension cord, and do not share the

singleoutletwithotherelectricalappliances.Otherwise,itwillcausefireorelectricalshock.

SAFETY PRECAUTIONS

CAUTION

WARNING

CAUTION

WARNING

Please read this installation manual carefully before operating the unit to ensure correct installation.

If the power cord is damaged, replacement work shall be performed by authorised personnel only.

Installation must be performed in accordance with the requirement of NEC and CEC by authorized

personnel only.

Contact an authorized service technician for repair, maintenance and installation of this unit.

This appliance is not intended for use by persons(including children) with reduced physical, sensory

or mental capabilities, or lack of experience and knowledge, unless they have been given supervision

or instruction concerning use of the appliance by persons responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

All the pictures in the instructions are for explanation purposes only. The actual shape should prevail.

The design and specifications are subject to change without prior notice for product improvement.

Consult with the sales agency or manufacturer for details.

There should not be any heat source or stream

near the unit.

There should not be any obstacles blocking the

air circulation.

A place where air circulation in the room is good.

A place where drainage can be easily done.

A place where noise prevention is taken into

consideration.

Do not install the unit near the door way.

Ensure the spaces indicated by arrows from the

wall,ceiling,fence or other obstacles.

There should not be any direct sunlight. If unavoidable,

sunlight prevention should be taken into consideration.

t d

ime

(WxH

)

A(mm) B(mm)

530

290

560

335

481

549

276

Mounting dimensions

670x540x265

780x540x250

760x590x285

845x700x320

Indoor unit

Outdoor unit

If an awning is built over the unit to prevent

direct sunsight or rain,be careful that heat

radiation from the condenser is not obstructed.

There should not be any animal or plant which

could be affected by hot air discharged.

Keep the spaces indicated by arrow from wall

ceiling, fence or other obstacles.

Do not place any obstacles which may cause

a short circuit of the discharged air.

Anchor the outdoor unit with a bolt and nut φ10 or

φ8 tightly and horizontally on a concrete or rigid mount.

Settlement of outdoor unit

NOTE: The outdoor unit you purchase may be like one

of the following. Install the outdoor unit according to the

dimension as indicated in the table below:

Air inlet

Air outlet

Air inlet

INSTALLATION PRECAUTIONS

CONNECT THE CABLE TO THE INDOOR UNIT

Terminal block of indoor unit

Connect the cable to the indoor unit

Before performing any electrical work, turn off the main power to the system.

1. The inside and outside connecting cable can be connected without removing the front grille.

2. The indoor power cord type is H05VV-F or H05V2V2-F, the outdoor power cord and

interconnected cord type is H07RN-F.

3. Lift the indoor unit panel up, remove the electrical box cover by loosening the screw.

4. Ensure the colour of wires of outdoor unit and the terminal Nos. are the same to the indoor s

respectively.

5. Wrap those cables not connected with terminals with insulation tapes, so that they will not touch

any electrical components. Secure the cable onto the control board with the cord clamp.

NOTE:

Electronic box

cover

Front Panel

To outdoor unit

Installation Plate

Clip Anchor

Self-tapping Screw A ST3.9x25

Seal(For cooling & heating models only)

Drain Joint(For cooling & heating models only）

Connecting

pipe

Assembly

Liquid side

Gas side

Remote controller

Self-tapping Screw B ST2.9x10

Φ6.35

Φ9.52

Φ12.7

Φ 16

Parts you must purchase. The pipe

size differ from appliance to appliance.

Consult the technician for the proper

size.

5-8(depending on models)

Except the above parts provided,the other parts needed during installation you must

purchase.

Remote controller holder

ACCESSORIES

Number

Name of Accessories

Qty

NOTE:

optional

parts

SELECT THE BEST LOCATION

CONNECTIVE PIPE AND DRAINAGE INSTALLATION

1. Run the drain hose sloping downward.

Do not install the drain hose as illustrated

in wrong figures.

2. When connecting extension drain hose,

insulate the connecting part of extension

drain hose with a shield pipe, do not let

the drain hose slack.

Drainage

Right

Wrong

Correct orientation

of Installation Plate

1. Fit the installation plate horizontally on

structural parts of the wall withspaces

around the installation plate.

2. If the wall is made of brick, concrete

or the like, drill five or eight 5mm

diameter holes in the wall. Insert

clip anchor for appropriate mounting

screws.

3. Fit the installation plate on the wall

with five or eight type A screws.

Mount the Installation Plate and drill

holes in the wall according to the wall

structure and corresponding mounting

points on the installation plate. The

installation plate providedwith the

machine differ from appliance

to appliance.(Dimensions are in

mm unless otherwise stated)

NOTE:

Installation Plate Mounting

The mounting wall is strong and solid enough

to prevent it from the vibration.

280

120mm or

more to wall

120mm or

more to wall

120mm or

more to wall

150mm or more to ceiling

Left rear side

refrigerant

pipe hole φ65

36.5

835

140

110

Left rear side

refrigerant

pipe hole φ65

Right rear side

refrigerant

pipe hole φ65

Right rear side

refrigerant

pipe hole φ65

Indoor unit outline

120mm or

more to wall

120mm or

more to wall

Indoor unit outline

990

315

135

260

150mm or more to ceiling

Left rear side

refrigerant

pipe hole φ65

Right rear side

refrigerant pipe

hole φ65

Model C

Model D

Model B

Model A

120mm or

more to wall

36.5

750

180

110

280

Right rear side

refrigerant pipe

hole φ65

Left rear side

refrigerant

pipe hole φ65

150mm or more to ceiling

Installation plate

Indoor unit outline

120mm or

more to wall

120mm or

more to wall

1186

21.5

275

343

549

590

325

333

810x558x310

900x860x315

Suggest Minimum Wire Size (AWG:American Wire Gage):

Appliance Amps

AW G Wire S ize

Air freshening filter(used to install on Air filter)

Electric safety regulations for the initial Installation

1. If there is serious safety problem about the power supply, the technicians should refuse to install

the air conditioner and explain to the client until the problem is solved.

2. Power voltage should be in the range of 90%~110%of rated voltage.

3. The surge protector and main power switch with a 1.5 times capacity of Max. Current of the unit should

be installed in power circuit. Ensure the air conditioner is grounded well.

4. The appliance shall be installed in accordance with national wiring regulations. Do not operate your air

conditioner in a wet room such as a bathroom or laundry room.

5. An all-pole disconnection device which has at least 3mm clearances in all poles, and have a leakage

current that may exceed 10mA, the residual current device(RCD) having a rated residual operating

current not exceeding 30mA, and disconnection must be incorporated in the fixed wiring in accordance

with the wiring rules.

6. For the unit adopts auxiliary electric heater, keep at least 1 meter away from the nearest combustible

materials.

7. According to the attached Electrical Connection Diagram located on the panel of the indoor & outdoor

unit to connect the wire.

8. All wiring must comply with local and national electrical codes and be installed by qualified and

skilled electricians.

9. An individual branch circuit and single receptacle used only for this air conditioner must be

available. See the following table for suggested wire sizes and fuse specifications:

Electrical work

The wire size of power supply cord and

interconnected wire and the current of the fuse or

switch are determined by the maximum current

indicated on the nameplate which located on the

side panel of the unit. Please refer to the nameplate

before selecting the wire size, fuse or switch.

The controller of the air conditioner designed with

a fuse protection function under abnormal

conditions, the specifications of the fuse have

printed on the circuit board, such as:

T3.15A/250VAC, T5A/250VAC, etc.

NOTE:

1 2

Inhaltsverzeichnis

Seite 1 - DRILL A HOLE IN THE WALL

1. Determine hole positions according to left and right side of the installation plate. The hole center is obtained by measuring the distance

Seite 2 - REFRIGERANT PIPE CONNECTION

Tel: (305)593-8358 Fax (305) 675-2212www.klimaire.com [email protected] NW 89 Place, Doral, FL 33172 - USAThe Klimaire logo is a registered

Kommentare zu diesen Handbüchern

Keine Kommentare

Klimaire KSIO018-H221 Installationshandbuch

Stöbern Sie online oder laden Sie Installationshandbuch nach Nein Klimaire KSIO018-H221 herunter. Klimaire KSIO018-H221 Installation Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Klimaire KSIO018-H221